[Printing] Menu

Initial values refer to the values set for the product when it was shipped from the factory. If you reset the product, the values set in the product are initialized. The table below shows the initial value of each setting item and whether it would be initialized.

• Normally, it is not necessary to perform the initialization. Doing an initialization removes all the product's settings that the customer changed.

Setting Item				Initial Value		Initialized by User Reset	Initialized by Factory Reset
				CL4NX	CL6NX
[Label Length]				203 dpi 20000 dots 305 dpi 18000 dots 609 dpi 9600 dots	203 dpi 20000 dots 305 dpi 18000 dots	Yes	Yes
[Label Width]				203 dpi 832 dots 305 dpi 1248 dots 609 dpi 2496 dots	If [Head Base Position] is [Standard] 203 dpi 1216 dots 305 dpi 1984 dots If [Head Base Position] is [Left-justify] 203 dpi 1340 dots 305 dpi 2010 dots	Yes	Yes
[Auto Measure]				Disabled		Yes	Yes
[Printing Mode]				Use Ribbon		Yes	Yes
[Ribbon Near End]				Enabled		Yes	Yes
[Speed]				203 dpi 6 ips 305 dpi 6 ips 609 dpi 4 ips Linerless mode 4 ips	203 dpi 6 ips 305 dpi 6 ips	Yes	Yes
[Sensor Type]				Gap None (When [Print Mode] is [Linerless])	Gap	Yes	Yes
[Auto-mode]				Enabled		Yes	Yes
[Print Mode]				Tear-Off (If no option is installed) Cutter (If cutter unit is installed) Dispenser (If dispenser unit is installed) Linerless (If linerless cutter kit is installed)	Tear-Off (If no option is installed) Cutter (If cutter unit is installed) Dispenser (If dispenser unit is installed)	Yes	Yes
[Backfeed]				Before (If [Print Mode] is set to [Tear-Off] or [Linerless]) After (If [Print Mode] is set to [Dispenser], [Cutter] or [Cut & Print]) None (If [Print Mode] is set to [Continuous])	Before (If [Print Mode] is set to [Tear-Off]) After (If [Print Mode] is set to [Dispenser], [Cutter] or [Cut & Print]) None (If [Print Mode] is set to [Continuous])	Yes	Yes
[Eject Cut]				Off		Yes	Yes
[Darkness Range]				A		Yes	Yes
[Darkness]				5		Yes	Yes
[Imaging]
	[Vertical]			0 dot		Yes	Yes
	[Horizontal]			0 dot		Yes	Yes
[Advanced]
	[Calibrate]
		[Auto-calibration]1		Gap + I-Mark		-	-
		[GAP Levels]		Value adjusted by the factory.		No	No
		[GAP Slice Level]		Auto		No	No
		[I-Mark Levels]		Value adjusted by the factory.		No	No
		[I-Mark Slice Level]		Auto		No	No
	[Head Check]			Off		Yes	Yes
	[Head Check Mode]			Always		Yes	Yes
	[Every Page]			1		Yes	Yes
	[Check Media Size]			Disabled		Yes	Yes
	[Adjustments]
		[Offset]		0 dot		No	No
		[Pitch]		0 dot		No	No
		[Pitch Offset]		0 dot		No	No
		[Darkness Adjust]		50		No	No
	[Start Online]			Enabled		Yes	Yes
	[Feed After Error]			Disabled		Yes	Yes
	[Feed At Power On]			Disabled		Yes	Yes
	[Finisher Feed]			0 dot (Standard)		Yes	Yes
	[Paper End]			Using I-mark		Yes	Yes
	[Head Base Position]			Standard		Yes	Yes
	[Prioritize]			Commands		Yes	Yes
	[Reprint]			Disabled		Yes	Yes
	[Print End Position]			0 dot		Yes	Yes
	[Label Near End]			Disabled		Yes	Yes

¹ Auto-calibration is not available for linerless models.