TOP > Adjusting the Product > Initializing the Product > List of Initial Values > [Interface] Menu [Interface] Menu Initial values refer to the values set for the product when it was shipped from the factory. If you reset the product, the values set in the product are initialized. The table below shows the initial value of each setting item and whether it would be initialized. • [Network] > [Settings] > [LAN] • [Network] > [Services] > [NTP]/[LPD]/[FTP]/[SNMP] • [Network] > [Services] > [Online Services] • [Network] > [Services] > [SATO App Storage]/[WebConfig] • [Network] > [Advanced] • [RS-232C]/[USB]/[NFC]/[Ignore CR/LF]/[Ignore CAN/DLE] • Normally, it is not necessary to perform the initialization. Doing an initialization removes all the product's settings that the customer changed. • [Network] > [Settings] > [LAN] Setting Item Initial Value Initialized by User Reset/Initialized by Factory Reset [IPv4] [Mode] DHCP Yes/Yes [DHCP] - - [IP Address] 0.0.0.0 Yes/Yes [Netmask] 255.255.255.0 Yes/Yes [Gateway] 0.0.0.0 Yes/Yes [DNS] 0.0.0.0, 0.0.0.0, 0.0.0.0 Yes/Yes [IPv6] [Mode] Disable Yes/Yes [DHCP] - - [IP Address] :: Yes/Yes [Prefix Length] 64 Yes/Yes [Gateway] :: Yes/Yes [DNS] :: Yes/Yes [Ports] [Port1] 1024 Yes/Yes [Port2] 1025 Yes/Yes [Port3] 9100 Yes/Yes [Flow Control] STATUS4 ENQ Yes/Yes [TCP Connection Queue] Enabled Yes/Yes [Legacy Status for Port 9100] Disabled Yes/Yes [BCC] Disabled Yes/Yes [Delay Reply ENQ] 0 ms Yes/Yes [Status4 Cyclic Response] 500 ms Yes/Yes [Proxy] [Enabled] Disabled Yes/Yes [Server] - Yes/Yes [Port No.] - Yes/Yes [Username] - Yes/Yes [Password] - Yes/Yes [Exclude] - Yes/Yes [DHCP Options] [Update DNS (Option 81)] Disabled Yes/Yes [Hostname] sato-lan-<serial No.> Yes/Yes • [Network] > [Services] > [NTP]/[LPD]/[FTP]/[SNMP] Setting Item Initial Value Initialized by User Reset/Initialized by Factory Reset [NTP] [Enable] Disabled No/Yes1 [Error] Disabled No/Yes1 [Time Server IP] 0.0.0.0 No/Yes1 [LPD] [Enable] Enabled Yes/Yes [DNS Lookup] Disabled Yes/Yes [FTP] [FTP] Disabled Yes/Yes [FTPS] Disabled Yes/Yes [FTPS Settings] [SSL/TLS Protocol] [TLS 1.0] Disabled Yes/Yes [TLS 1.1] Disabled Yes/Yes [TLS 1.2] Enabled - [Cipher Suites] Recommended Yes/Yes [Timeout] 300 sec Yes/Yes [SNMP] [sysContact] - Yes/Yes [sysName] - Yes/Yes [sysLocation] - Yes/Yes [prtMarkerCounterUnit] meters Yes/Yes [Agent] [Enable] Enabled Yes/Yes [Read-Only] [SNMP Version] 1|2c|3 Yes/Yes [Community] - Yes/Yes [User] rouser Yes/Yes [User Security] None Yes/Yes [Authentication Protocol] MD5 Yes/Yes [Authentication Passphrase] - Yes/Yes [Privacy Protocol] DES Yes/Yes [Privacy Passphrase] - Yes/Yes [Read-Write] [SNMP Version] Disabled Yes/Yes [Community] - Yes/Yes [User] rwuser Yes/Yes [User Security] None Yes/Yes [Authentication Protocol] MD5 Yes/Yes [Authentication Passphrase] - Yes/Yes [Privacy Protocol] DES Yes/Yes [Privacy Passphrase] - Yes/Yes [Traps] [Enable] Disabled Yes/Yes [SNMP Version] 1 Yes/Yes [IP Version] 4 Yes/Yes [Destinations] 1 Yes/Yes [Destination 1] 0.0.0.0 Yes/Yes [Destination 2] 0.0.0.0 Yes/Yes [Destination 3] 0.0.0.0 Yes/Yes [Community] - Yes/Yes [User] trapuser Yes/Yes [Engine ID] Hex string generated from MAC address Yes/Yes [Security] None Yes/Yes [Authentication Protocol] MD5 Yes/Yes [Authentication Passphrase] - Yes/Yes [Privacy Protocol] DES Yes/Yes [Privacy Passphrase] - Yes/Yes • [Network] > [Services] > [Online Services] Setting Item Initial Value Initialized by User Reset/Initialized by Factory Reset [SOS Mode] Disabled No/No [Allow Remote Control] Always No/No [MQTT Protocol] MQTT over WebSocket No/No [MQTT Proxy enabled] Enabled No/No [Add Device] - - [Contact Information] [Phone Number] - - [Periodic Notification] [Type] Disabled No/No [Counter] Thermal Head No/No [Head] [Meters] 1,000 No/No [Last Update] - No/No [Next Update] - No/No [Current Value] - No/No [Cutter] [Cuts] 10,000 No/No [Last Update] - No/No [Next Update] - No/No [Current Value] - No/No [Notifications] 1 No/No [Time 1] 00:00 No/No [Time 2] 00:00 No/No [Time 3] 00:00 No/No [Weekday] Monday No/No [Day] 1 No/No [Time] 00:00 No/No [Update Screen] Normal No/No [QR code offset] [Vertical] 0 dot No/No [Horizontal] 0 dot No/No [Daily Checkup] - - [Port diagnostic] - - [Restore SOS Agent] - - • [Network] > [Services] > [SATO App Storage]/[WebConfig] Setting Item Initial Value Initialized by User Reset/Initialized by Factory Reset [SATO App Storage] - - [WebConfig] [SSL/TLS Protocol] [TLS 1.0] Disabled Yes/Yes [TLS 1.1] Disabled Yes/Yes [TLS 1.2] Enabled - [Cipher Suites] Recommended Yes/Yes • [Network] > [Advanced] Setting Item Initial Value Initialized by User Reset/Initialized by Factory Reset [ARP Announcement] [Additional] Enabled Yes/Yes [Periodic] Off Yes/Yes [Firewall] [Enable] Disabled Yes/Yes [Allow Services And Ports] [Data Ports] Enabled Yes/Yes [FTP] Disabled Yes/Yes [FTPS] Disabled Yes/Yes [LPD] Enabled Yes/Yes [MAILC] Enabled Yes/Yes [NTP] Disabled No/Yes1 [Online Services] Disabled No/No [PING] Enabled Yes/Yes [Proxy] Disabled Yes/Yes [SATO All-In-One Tool] Enabled Yes/Yes [SATO App Storage] Enabled Yes/Yes [SCP] Enabled Yes/Yes [SNMP Agent] Enabled Yes/Yes [WEBC] Enabled Yes/Yes [WebConfig] Enabled Yes/Yes [Custom Settings] [TCP Source Port] [Existing Port No.] 22 80 443 465 587 8080 - [Additional Port No.] - Yes/Yes [TCP Destination Port] [Existing Port No.] 80 443 515 1024 1025 9100 - [Additional Port No.] - Yes/Yes [UDP Source Port] [Existing Port No.] 53 - [Additional Port No.] - Yes/Yes [UDP Destination Port] [Existing Port No.] 68 161 19541 - [Additional Port No.] - Yes/Yes [ICMP Type] [Existing ICMP Type] 0 8 - [Additional ICMP Type] - Yes/Yes • [RS-232C]/[USB]/[NFC]/[Ignore CR/LF]/[Ignore CAN/DLE] Setting Item Initial Value Initialized by User Reset/Initialized by Factory Reset [RS-232C] [Baudrate] 115200 Yes/Yes [Parameters] 8-N-1 Yes/Yes [Flow Control] STATUS4 Yes/Yes [BCC] Disabled Yes/Yes [USB] [Flow Control] STATUS4 Yes/Yes [BCC] Disabled Yes/Yes [Change USB Serial] Disabled No/Yes1 [NFC] [I/F Enable] Enabled Yes/Yes [Ignore CR/LF] Disabled Yes/Yes [Ignore CAN/DLE] Disabled Yes/Yes 1Can also be initialized by [Factory Reset (-Interface)] Related Topics [Reset] Back to top
