[Interface] Menu

Initial values refer to the values set for the product when it was shipped from the factory. If you reset the product, the values set in the product are initialized. The table below shows the initial value of each setting item and whether it would be initialized.

• Normally, it is not necessary to perform the initialization. Doing an initialization removes all the product's settings that the customer changed.

Setting Item						Initial Value	Initialized by User Reset	Initialized by Factory Reset
[Network]
	[Settings]
		[LAN]
			[IPv4]
				[Mode]		DHCP	Yes	Yes
				[DHCP]		-	-	-
				[IP Address]		0.0.0.0	Yes	Yes
				[Netmask]		255.255.255.0	Yes	Yes
				[Gateway]		0.0.0.0	Yes	Yes
				[DNS]		0.0.0.0	Yes	Yes
			[IPv6]
				[Mode]		Disable	Yes	Yes
				[DHCP]		-	-	-
				[IP Address]		::	Yes	Yes
				[Prefix Length]		64	Yes	Yes
				[Gateway]		::	Yes	Yes
				[DNS]		::	Yes	Yes
			[Proxy]
				[Enabled]		Disabled	Yes	Yes
				[Server]		-	Yes	Yes
				[Port No.]		-	Yes	Yes
				[Username]		-	Yes	Yes
				[Password]		-	Yes	Yes
				[Exclude]		-	Yes	Yes
			[DHCP Options]
				[Update DNS (Option 81)]		Disabled	Yes	Yes
				[Hostname]		sato-lan-<serial No.>	Yes	Yes
		[Interface]				Auto	Yes	Yes
	[Services]
		[Ports]
			[Port1]			1024	Yes	Yes
			[Port2]			1025	Yes	Yes
			[Port3]			9100	Yes	Yes
			[Flow Control]			StatusL	Yes	Yes
			[TCP Connection Queue]			Disabled	Yes	Yes
			[Legacy Status for Port 9100]			Disabled	Yes	Yes
			[ENQ Reply Delay]			0 ms	Yes	Yes
			[Status4 Cyclic Response]			500 ms	Yes	Yes
			[BCC]			Disabled	Yes	Yes
			[StatusL]			Standard	Yes	Yes
		[NTP]
			[Enable]			Disabled	No	Yes1
			[Error]			Disabled	No	Yes1
			[Time Server IP]			0.0.0.0	No	Yes1
		[LPD]
			[Enable]			Enabled	Yes	Yes
			[DNS Lookup]			Disabled	Yes	Yes
		[FTP]
			[FTP]			Disabled	Yes	Yes
			[FTPS]			Disabled	Yes	Yes
			[FTPS Settings]
				[SSL/TLS Protocol]
					[SSL 3.0]	Disabled	Yes	Yes
					[TLS 1.0]	Disabled	Yes	Yes
					[TLS 1.1]	Disabled	Yes	Yes
					[TLS 1.2]	Enabled	-	-
				[Cipher Suites]		Recommended	Yes	Yes
			[Timeout]			300 sec	Yes	Yes
		[SNMP]
			[sysContact]			-	Yes	Yes
			[sysName]			-	Yes	Yes
			[sysLocation]			-	Yes	Yes
			[prtMarkerCounterUnit]			meters	Yes	Yes
			[Agent]
				[Enable]		Enabled	Yes	Yes
[Read-Only]
				[SNMP Version]	1|2c|3	Yes	Yes
				[Community]	-	Yes	Yes
				[User]	rouser	Yes	Yes
				[User Security]	None	Yes	Yes
				[Authentication Protocol]	MD5	Yes	Yes
				[Authentication Passphrase]	-	Yes	Yes
				[Privacy Protocol]	DES	Yes	Yes
				[Privacy Passphrase]	-	Yes	Yes
			[Read-Write]
				[SNMP Version]	Disabled	Yes	Yes
				[Community]	-	Yes	Yes
				[User]	rwuser	Yes	Yes
				[User Security]	None	Yes	Yes
				[Authentication Protocol]	MD5	Yes	Yes
				[Authentication Passphrase]	-	Yes	Yes
				[Privacy Protocol]	DES	Yes	Yes
				[Privacy Passphrase]	-	Yes	Yes
		[Traps]
			[Enable]		Disabled	Yes	Yes
			[SNMP Version]		1	Yes	Yes
			[IP Version]		4	Yes	Yes
			[Destinations]		1	Yes	Yes
			[Destination 1]		0.0.0.0	Yes	Yes
			[Destination 2]		0.0.0.0	Yes	Yes
			[Destination 3]		0.0.0.0	Yes	Yes
			[Community]		-	Yes	Yes
			[User]		trapuser	Yes	Yes
			[Engine ID]		Hex string generated from MAC address	Yes	Yes
			[Security]		None	Yes	Yes
			[Authentication Protocol]		MD5	Yes	Yes
			[Authentication Passphrase]		-	Yes	Yes
			[Privacy Protocol]		DES	Yes	Yes
			[Privacy Passphrase]		-	Yes	Yes
	[Online Services]
		[SOS Mode]			Disabled	No	No
		[Allow Remote Control]			Always	No	No
		[MQTT Protocol]			MQTT over WebSocket	No	No
		[MQTT Proxy enabled]			Enabled	No	No
		[Add Device]			-	-	-
		[Contact Information]
			[Phone Number]		-	No	No
		[Periodic Notification]
			[Type]		Disabled	No	No
			[Counter]		Head	No	No
			[Head]		-	-	-
				[Meters]	1,000	No	No
				[Last Update]	-	No	No
				[Next Update]	-	No	No
				[Current Value]	-	No	No
			[Notifications]		1	No	No
			[Weekday]		Sunday	No	No
			[Day]		2	No	No
			[Time 1]		00:00	No	No
			[Time 2]		00:00	No	No
			[Time 3]		00:00	No	No
			[Time]		00:00	No	No
		[Update Screen]			Normal	No	No
		[QR code offset]			-	-	-
		[Daily Checkup]			-	-	-
		[Port diagnostic]			-	-	-
		[Restore SOS Agent]			-	-	-
	[WebConfig]
		[SSL/TLS Protocol]
			[SSL 3.0]		Disabled	Yes	Yes
			[TLS 1.0]		Disabled	Yes	Yes
			[TLS 1.1]		Disabled	Yes	Yes
			[TLS 1.2]		Enabled	-	-
		[Cipher Suites]			Recommended	Yes	Yes
[Advanced]
	[ARP Announcement]
		[Additional]			Enabled	Yes	Yes
		[Periodic]			300 sec	Yes	Yes
	[Firewall]
		[Enable]			Disabled	Yes	Yes
		[Allow Services And Ports]
			[Data Ports]		Enabled	Yes	Yes
			[FTP]		Disabled	Yes	Yes
			[FTPS]		Disabled	Yes	Yes
			[LPD]		Enabled	Yes	Yes
			[MAILC]		Enabled	Yes	Yes
			[NTP]		Disabled	No	Yes1
			[Online Services]		Disabled	No	No
			[PING]		Enabled	Yes	Yes
			[Proxy]		Disabled	Yes	Yes
			[SATO All-In-One Tool]		Enabled	Yes	Yes
			[SCP]		Enabled	Yes	Yes
			[SNMP Agent]		Enabled	Yes	Yes
			[WEBC]		Enabled	Yes	Yes
			[WebConfig]		Enabled	Yes	Yes
		[Custom Settings]
			[TCP Source Port]
				[Existing Port No.]	-	-	-
				[Additional Port No.]	-	Yes	Yes
			[TCP Destination Port]
				[Existing Port No.]	-	-	-
				[Additional Port No.]	-	Yes	Yes
			[UDP Source Port]
				[Existing Port No.]	-	-	-
				[Additional Port No.]	-	Yes	Yes
			[UDP Destination Port]
				[Existing Port No.]	-	-	-
				[Additional Port No.]	-	Yes	Yes
			[ICMP Type]
				[Existing ICMP Type]	-	-	-
				[Additional ICMP Type]	-	Yes	Yes
[IEEE1284]
	[Flow Control]					StatusL	Yes	Yes
	[StatusL]					Standard	Yes	Yes
	[BCC]					Disabled	Yes	Yes
[RS-232C]
	[Baudrate]					115200	Yes	Yes
	[Parameters]					8-N-1	Yes	Yes
	[Flow Control]					StatusL	Yes	Yes
	[StatusL]					Standard	Yes	Yes
	[BCC]					Disabled	Yes	Yes
[Ignore CR/LF]						Disabled	Yes	Yes
[Ignore CAN/DLE]						Disabled	Yes	Yes

¹ Can also be initialized by [Factory Reset (-Interface)]

---

Related Topics

[Reset]