[Applications] Menu

Initial values refer to the values set for the product when it was shipped from the factory. If you reset the product, the values set in the product are initialized. The table below shows the initial value of each setting item and whether it would be initialized.

• Normally, it is not necessary to perform the initialization. Doing an initialization removes all the product's settings that the customer changed.

Setting Item				Initial Value	Initialized by User Reset	Initialized by Factory Reset
[Applicator]
	[Completion Output Time]			200 ms	No	Yes
	[Suction Sensor Setting]
		[Sensor Type]		Fiber	No	Yes
		[Suction Switching Check Time]		30	No	Yes
	[Apply Adjustment]
		[Conveyor Speed]		18	No	Yes
		[Apply Position Adjustment Method]		Timing	No	Yes
		[Apply Position No.]		01:Name01	No	Yes
		[Timing]		0	No	Yes
		[Position]		0	No	Yes
		[Product Length]		0	No	Yes
		[Pressure Bonding Time]		100	No	Yes
		[Blowing Time]		100	No	Yes
		[Liner Rewinding Adjustment]		30	No	Yes
		[Setting 1]		0	No	Yes
		[Setting 2]		0	No	Yes
		[Setting 3]		0	No	Yes
		[Setting 4]		0	No	Yes
		[Setting 5]		0	No	Yes
	[Warning Lamp]
		[Select Type]		Three Color Lamp with buzzer	No	Yes
		[At run-time]		Green on	No	Yes
		[In error]		Red blinking	No	Yes
		[Stopped]		Off	No	Yes
		[Detect label end]		Yellow on	No	Yes
		[Warning]		Yellow blinking	No	Yes
		[Notification Display]		Enabled	No	Yes
		[Low label detection buzzer]		Disabled	No	Yes
		[Label End Detection Buzzer]		Disabled	No	Yes
	[Detailed Setting]
		[Delivery Method]
			[Select]	Print and Wait	No	Yes
			[CJ/SJ Print and Wait]	Wait at Front End	No	Yes
		[Item Completion Condition]		Apply End	No	Yes
		[Process at Origin Off]		Error	No	Yes
		[Label Remain Error Check Select]		Return to Origin	No	Yes
		[Blow Action at PJ Miss]		Disabled	No	Yes
		[Idling at Start]		Disabled	No	Yes
		[Reset Key Press Display]		Disabled	No	Yes
		[Cancel With Reset]		Disabled	No	Yes
		[Mechanical Confirmation]
			[Liner Rewinding Confirmation]	Enabled	No	Yes
			[Nip Roller Lever Confirmation]	Enabled	No	Yes
	[Compatible]
		[LR4800RV Compatible Mode]
			[Apply Ready Signal]	Disabled	No	Yes
			[Return Status]	Disabled	No	Yes
[Protocol]				SBPL	Yes	Yes
[Auto Switch Group]
	[SBPL]			Enabled	Yes	Yes
	[SZPL]			Enabled	Yes	Yes
	[SIPL]			Enabled	Yes	Yes
	[SDPL]			Enabled	Yes	Yes
[SBPL]
	[Show Error]			Disabled	Yes	Yes
	[Standard Code]			Enabled	Yes	Yes
	[Orientation]1			Portrait	Yes	Yes
	[Font Settings]
		[Zero Slash]		Disabled	Yes	Yes
		[Kanji]
			[Kanji Set]	JP-JISX0208	Yes	Yes
			[Character Code]	SJIS	Yes	Yes
			[Kanji Style]	Gothic	Yes	Yes
		[Proportional]		Disabled	Yes	Yes
		[Code Page]		X201	Yes	Yes
		[€]		d5	Yes	Yes
	[Compatible]
		[M-8400 Compatibility]		Disabled	Yes	Yes
		[CODE128(C) Zero Fill]		Disabled	Yes	Yes
		[Kanji Command]		Disabled	Yes	Yes
		[Call Font/Logo]		Disabled	Yes	Yes
		[OCR Font]		Enabled	Yes	Yes
		[PDF417 ECC Level fixed]		Disabled	Yes	Yes
		[Human Readable Overwrite]		Disabled	Yes	Yes
[SZPL]
	[Label]
		[Shift]		0 dot	Yes	Yes
		[Top]		0 dot	Yes	Yes
	[Label Rotation]			0 degree	Yes	Yes
	[Caret]			94 (^)	Yes	Yes
	[Delimiter]			44 (,)	Yes	Yes
	[Tilde]			126 (~)	Yes	Yes
	[Clock Format]			(none)	Yes	Yes
	[Default Font]			(none)	Yes	Yes
	[Format Convert]			(none)	Yes	Yes
[SIPL]
	[Font Settings]
		[Code Page]		1252	Yes	Yes
		[New Font Encoding]		Disabled	Yes	Yes
		[c20 Proportional Pitch]		Disabled	Yes	Yes
		[Zero Slash]		Disabled	Yes	Yes
	[Format Save]			Enabled	Yes	Yes
	[Label Rotation]			0 degree	Yes	Yes
[SDPL]
	[Control Code]
		[Code Type]		Standard	Yes	Yes
		[SOH]		01	Yes	Yes
		[STX]		02	Yes	Yes
		[CR]		0D	Yes	Yes
		[CNTBY]		5E	Yes	Yes
	[Label Rotation]			0 degree	Yes	Yes
	[SOP Emulation]			Auto	Yes	Yes
	[Compatible Mode]
		[TTF]		Disabled	Yes	Yes
		[Graphics]		Disabled	Yes	Yes
		[Compression]		Disabled	Yes	Yes
	[Right-to-Left print]1			Auto	Yes	Yes
	[Receive TimeOut]			0 (Off)	Yes	Yes
	[Blank Item Feed]			Enabled	Yes	Yes
	[Prioritize]
		[Format Attribute]1		Commands	Yes	Yes
		[Pause Mode]1		Commands	Yes	Yes
		[1 Byte Codepage]1		Commands	Yes	Yes
		[SDPL Measure Unit]1		Commands	Yes	Yes
		[Scalable Font Style]1		Commands	Yes	Yes
		[Sensor Type]1		Commands	Yes	Yes
		[Feedback Character]1		Commands	Yes	Yes
		[SOH Commands]1		Commands	Yes	Yes
		[Module Selection]1		Commands	Yes	Yes
	[Format Attribute]			XOR	Yes	Yes
	[Pause Mode]			Disabled	Yes	Yes
	[1 Byte Codepage]			CP 850	Yes	Yes
	[SDPL Measure Unit]			Inch	Yes	Yes
	[Scalable Font Style]
		[Bold]		Disabled	Yes	Yes
		[Italic]		Disabled	Yes	Yes
	[Feedback Character]1			Enabled	Yes	Yes
	[SOH Commands]
		[All Commands]1		Enabled	Yes	Yes
		[SOH-B Command]1		Enabled	Yes	Yes
		[SOH-C Command]1		Enabled	Yes	Yes
		[Others]1		Enabled	Yes	Yes
	[Module Selection]			A	Yes	Yes
[AEP]
	[Enable]			Disabled	No	Yes
	[Starting Application]			Standard Demo (/rom/ standalone/ sa.lua)	No	Yes
	[Delete Application]			-	-	-
	[Label Rotation]			Disabled	Yes	Yes

¹ Can also be initialized by [Printing] is selected in [Select]

---

Related Topics

[Reset]