[SDPL] Settings

To use SDPL as a printer command, set the following items:

• The items below the [Prioritize] menu can be set only if you have selected [Settings] in the [Prioritize] menu.

[Control Code]

Set the control code.

The setting items are as follows:

[Code Type]

Set the type of the control code.

[SOH]

Set the SOH code.

You can change the code only if you have selected [Custom] in the [Code Type] menu.

The setting range is from 0 to FF (hexadecimal).

• Each code must be set to different values.

[STX]

Set the STX code.

You can change the code only if you have selected [Custom] in the [Code Type] menu.

The setting range is from 0 to FF (hexadecimal).

• Each code must be set to different values.

[CR]

Set the CR code.

You can change the code only if you have selected [Custom] in the [Code Type] menu.

The setting range is from 0 to FF (hexadecimal).

• Each code must be set to different values.

[CNTBY]

Set the CNTBY code.

You can change the code only if you have selected [Custom] in the [Code Type] menu.

The setting range is from 0 to FF (hexadecimal).

• Each code must be set to different values.

[Compatible Mode]

Set the compatible mode for SDPL.

The setting items are as follows:

[TTF]

Enable or disable TrueType font compatible mode.

[Graphics]

Set whether to allow the registration of graphic data even if a line feed code is omitted.

[Compression]

Set whether to support graphic data created using unique compression formats.

[Prioritize]

Select the settings to be prioritized for each setting item of the SDPL command. You can set whether to prioritize settings via the printer or commands.

When you select [Settings] for an item, the setting specified in the [SDPL] menu of the printer will be used.

The setting items are as follows:

[Format Attribute]

Set whether to prioritize the settings via the printer or commands for the format attribute setting.

[Pause Mode]

Set whether to prioritize the settings via the printer or commands for the pause mode setting.

[1 Byte Codepage]

Set whether to prioritize the settings via the printer or commands for the 1-byte code page setting.

[SDPL Measure Unit]

Set whether to prioritize the settings via the printer or commands for the measurement unit setting.

[Scalable Font Style]

Set whether to prioritize the settings via the printer or commands for the scalable font style settings.

[Sensor Type]

Set whether to prioritize the settings via the printer or commands for the sensor type setting.

[Feedback Character]

Set whether to prioritize the settings via the printer or commands for the feedback character setting.

[SOH Commands]

Set whether to prioritize the settings via the printer or commands for the SOH command settings.

[Module Selection]

Set whether to prioritize the settings via the printer or commands for the module selection setting.

[Scalable Font Style]

Set the style of the scalable fonts.

You can change this setting only if you have selected [Settings] in the [Prioritize] > [Scalable Font Style] menu.

The setting items are as follows:

[Bold]

Set whether to use bold for the scalable fonts.

[Italic]

Set whether to use italics for the scalable fonts.

[SOH Commands]

Set the SOH commands.

You can change this setting only if you have selected [Settings] in the [Prioritize] > [SOH Commands] menu.

The setting items are as follows:

[All Commands]

Enable or disable all SOH commands. Or, make it possible to perform settings for each command.

[SOH-B Command]

Enable or disable the SOH-B command.

You can change this setting only if you have selected [Custom] in the [All Commands] menu.

[SOH-C Command]

Enable or disable the SOH-C command.

You can change this setting only if you have selected [Custom] in the [All Commands] menu.

[Others]

Enable or disable the SOH commands, except for the SOH-B and SOH-C commands.

You can change this setting only if you have selected [Custom] in the [All Commands] menu.

[Label Rotation]

Set the page orientation for label printing.

The label size set in the printer is used as a reference for rotation.

[SOP Emulation]

Set the SOP emulation.

[Right-to-Left print]

Set the Right-to-Left printing function.

[Receive Timeout]

Set the time period that the printer stays in the mode to receive binary data.

When the specified time period has passed, the printer’s binary reception mode ends, and the SDPL commands are scanned.

[Blank Item Feed]

Set whether to feed a label with nothing printed on it when the printer receives label formatting commands that do not generate any printable image.

[Format Attribute]

Set the format attribute.

You can change this setting if you have selected [Settings] in the [Prioritize] > [Format Attribute] menu.

[Pause Mode]

Enable or disable the pause mode.

You can change this setting only if you have selected [Settings] in the [Prioritize] > [Pause Mode] menu.

[1 Byte Codepage]

Select the code page to be used for 1-byte characters from the list.

You can change this setting only if you have selected [Settings] in the [Prioritize] > [1 Byte Codepage] menu.

[SDPL Measure Unit]

Set the measurement unit.

You can change this setting only if you have selected [Settings] in the [Prioritize] > [SDPL Measure Unit] menu.

[Feedback Character]

Enable or disable the <STX>a command.

You can change this setting only if you have selected [Settings] in the [Prioritize] > [Feedback Character] menu.

[Module Selection]

Select a location to save the settings of the printer.

You can change this setting only if you have selected [Settings] in the [Prioritize] > [Module Selection] menu.