Usable Media

• Use our specified supply products.

　

Type

•	Media roll (Face-in wound/face-out wound)

•	Fan-fold media

　

Size

•	Continuous/Tear-Off/Dispenser

Item	Description
Media Length	16 to 500 mm (0.63" to 19.69") 1
Media Length (With Liner)	19 to 503 mm (0.75" to 19.80")
Media Width	25 to 82 mm (0.98" to 3.23")
Media Width (With Liner)	28 to 82 mm (0.98" to 3.23") (butt cut label) / 28 to 85 mm (1.10" to 3.35") (others)

1 If you are printing labels that are more than 100 mm (3.94") long in dispenser mode, the labels will stick to the table on which the product is placed, so you should do a test print to check the operation before you start.

• Above pitch and width are valid for die-cut labels. For media without liner like tags, refer to the value 'with liner'.

　

•	Cutter/Partial Cutter

Item	Description
Media Length	30 to 500 mm (1.18" to 19.69")
Media Length (With Liner)	33 to 503 mm (1.30" to 19.80")
Media Width	25 to 82 mm (0.98" to 3.23")
Media Width (With Liner)	28 to 82 mm (0.98" to 3.23") (butt cut label) / 28 to 85 mm (1.10" to 3.35") (others)

• Above pitch and width are valid for die-cut labels. For media without liner like tags, refer to the value 'with liner'.

　

•	Linerless Tearoff

Item	Description
Media Length	20 to 500 mm (0.79" to 19.69") 1 2
Media Width	32 to 82 mm (1.26" to 3.23")

1 If you are printing media that is 20 to 23 mm (0.79 to 0.91") long, set the print speed to 5 ips (127 mm/sec) or less.

2 If you are printing labels that are more than 100 mm (3.94") long, the labels will stick to the table on which the product is placed, so you should do a test print to check the operation before you start.

　

•	Linerless Cutter

• To use linerless labels, contact your SATO sales representative for more details about the specifications.

Item	Description
Media Length	45 to 500 mm (1.77" to 19.69") 1

1 If you are printing labels that are more than 100 mm (3.94") long, the labels will stick to the table on which the product is placed, so you should do a test print to check the operation before you start.

• The usable media sizes, the output speed and print quality vary depending on the media specification, media, product settings and outputting environment. It is recommended to perform a test print with the media to be used in advance.

　

Core Diameter (Media Roll)

•	When using the standard model, optional cutter kit, partial cutter kit, linerless cutter kit, battery mount kit, or cradle kit

◦	φ26 mm (φ1") core

◦	φ40 mm (φ1.5") core

• Set the flap position of the media guide to the lower position (initial value) when using the φ26 mm (φ1 ") core, and the upper position when using the φ40 mm (φ1.5") core.

•	When using the optional wall mount kit

φ26 mm (φ1") core

• Set the flap position of the media guide to the lower position (initial value).

Roll Diameter (Media Roll)

•	When using the standard model, optional cutter kit, partial cutter kit, linerless cutter kit, battery mount kit, or cradle kit

◦	φ26 mm (φ1") core

Maximum φ105 mm (φ4.13")

◦	φ40 mm (φ1.5") core

Maximum φ90 mm (φ3.54")

•	When using the optional wall mount kit

Maximum φ90 mm (φ3.54")

　

Height (Fan-fold Media)

(A) Media height (from desk): within 100 mm (3.94")

(B) Distance between the back side of the product and the media: 150 mm (5.91") or more

• The height may be limited depending on where media is placed. • When drawing the media from under the desk, not from the position on the same desk which the rear side of the product is placed, place the media so as not to obstruct the printing operation. • Fan-fold media is not available in dispenser mode since the perforated line affects the dispenser function.

　

Thickness

•	140 to 190 μm (0.14 to 0.19 mm (0.0055" to 0.0075"))