TOP > Adjusting the Product > Initializing the Product > List of Initial Values > [Interface] Menu [Interface] Menu Initial values refer to the values set for the product when it was shipped from the factory. If you reset the product, the values set in the product are initialized. The table below shows the initial value of each setting item and whether it would be initialized. • [Network] > [Settings] > [Wi-Fi] • [Network] > [Services] > [NTP]/[LPD]/[FTP]/[SFTP]/[SNMP] • [Network] > [Services] > [Online Services] • [Network] > [Services] > [SOTI Connect] • [Network] > [Advanced] • [USB]/[Bluetooth]/[NFC]/[Ignore CR/LF]/[Ignore CAN/DLE] • Normally, it is not necessary to perform the initialization. Doing an initialization removes all the product's settings that the customer changed. • [Network] > [Settings] > [Wi-Fi] Setting Item Initial Value Initialized by User Reset/Factory Reset [IPv4] [Mode] [DHCP] Yes/Yes [DHCP] - - [IP Address] 0.0.0.0 Yes/Yes [Netmask] 255.255.255.0 Yes/Yes [Gateway] 0.0.0.0 Yes/Yes [DNS] 0.0.0.0, 0.0.0.0, 0.0.0.0 Yes/Yes [IPv6] [Mode] [Disable] Yes/Yes [DHCP] - - [IP Address] :: Yes/Yes [Prefix Length] 64 Yes/Yes [Gateway] :: Yes/Yes [DNS] :: Yes/Yes [Ports] [Port1] 1024 Yes/Yes [Port2] 1025 Yes/Yes [Port3] 9100 Yes/Yes [Flow Control] [STATUS4 ENQ] Yes/Yes [TCP Connection Queue] [Enabled] Yes/Yes [Legacy Status for Port 9100] [Disabled] Yes/Yes [Delay Reply ENQ] 0 ms Yes/Yes [Proxy] [Enabled] [Disabled] Yes/Yes [Server] - Yes/Yes [Port No.] - Yes/Yes [Username] - Yes/Yes [Password] - Yes/Yes [Exclude] - Yes/Yes [DHCP Options] [Update DNS (Option 81)] [Disabled] Yes/Yes [Hostname] sato-wlan-serial number Yes/Yes [Hostname (Option 12)] [Disabled] Yes/Yes [Hostname Suffix] Printer serial number Yes/Yes [UserClass (Option 77)] [Disabled] Yes/Yes [UserClass] [PTR] Yes/Yes [Wi-Fi Protected Setup(WPS)] - - [Wi-Fi Direct] [Device Name] SATO_PRINTER Yes/Yes [Band] [All] Yes/Yes [SSID] SATO_PRINTER Yes/Yes [Hidden SSID] [Enabled] Yes/Yes [Mode] [Infrastructure] Yes/Yes [Channel] 6 Yes/Yes [Security] [None] Yes/Yes [WEP Conf.] [Authentication] [Open System] Yes/Yes [Key Index] 1 Yes/Yes [Key #1] to [Key #4] - Yes/Yes [WPA Conf.] [WPA Authentication] [Personal (PSK)] Yes/Yes [PSK] - Yes/Yes [EAP Conf.] [EAP Mode] [FAST] Yes/Yes [Inner Method] [AUTO] Yes/Yes [Username] - Yes/Yes [Password] - Yes/Yes [Anon. Outer ID] - Yes/Yes [Verify Server Cert.] [Enabled] Yes/Yes [Private Key P/W] - Yes/Yes [PAC Auto Provisioning] [Disabled] Yes/Yes [PAC Password] - Yes/Yes • [Network] > [Services] > [NTP]/[LPD]/[FTP]/[SFTP]/[SNMP] Setting Item Initial Value Initialized by User Reset/Factory Reset [NTP] [Enable] [Disabled] No/Yes1 [Error] [Disabled] No/Yes1 [Time Server IP] 0.0.0.0 No/Yes1 [LPD] [Enable] [Enabled] Yes/Yes [DNS Lookup] [Disabled] Yes/Yes [FTP] [Enable] [Disabled] Yes/Yes [FTP Timeout] 300 sec Yes/Yes [SFTP] [Enable] [Disabled] Yes/Yes [SFTP Timeout] 300 seconds Yes/Yes [Authentication Method] [Password Authentication] Yes/Yes [Password Authentication] [User] sftpuser - [Password] - Yes/Yes [Key Authentication] [User] sftpuser - [Public Key] [Unregistered] Yes/Yes [SNMP] [sysContact] - Yes/Yes [sysName] - Yes/Yes [sysLocation] - Yes/Yes [prtMarkerCounterUnit] [meters] Yes/Yes [Agent] [Enable] [Enabled] Yes/Yes [Read-Only] [SNMP Version] [1|2c|3] Yes/Yes [Community] - Yes/Yes [User] rouser Yes/Yes [User Security] [None] Yes/Yes [Authentication Protocol] [MD5] Yes/Yes [Authentication Passphrase] - Yes/Yes [Privacy Protocol] [DES] Yes/Yes [Privacy Passphrase] - Yes/Yes [Read-Write] [SNMP Version] [Disabled] Yes/Yes [Community] - Yes/Yes [User] rwuser Yes/Yes [User Security] [None] Yes/Yes [Authentication Protocol] [MD5] Yes/Yes [Authentication Passphrase] - Yes/Yes [Privacy Protocol] [DES] Yes/Yes [Privacy Passphrase] - Yes/Yes [Traps] [Enable] [Disabled] Yes/Yes [SNMP Version] 1 Yes/Yes [IP Version] 4 Yes/Yes [Destinations] 1 Yes/Yes [Destination 1] 0.0.0.0 Yes/Yes [Destination 2] 0.0.0.0 Yes/Yes [Destination 3] 0.0.0.0 Yes/Yes [Community] - Yes/Yes [User] trapuser Yes/Yes [Engine ID] Number generated from codes unique to each product Yes/Yes [Security] [None] Yes/Yes [Authentication Protocol] [MD5] Yes/Yes [Authentication Passphrase] - Yes/Yes [Privacy Protocol] [DES] Yes/Yes [Privacy Passphrase] - Yes/Yes • [Network] > [Services] > [Online Services] Setting Item Initial Value Initialized by User Reset/Factory Reset [SOS Mode] [Disabled] No/No [Allow Remote Control] [Always] No/No [MQTT Protocol] [MQTT] No/No [Add Device] - - [Contact Information] [Phone Number] - - [Periodic Notification] [Type] [Disabled] No/No [Counter] [Thermal Head] No/No [Head] [Meters] 1,000 No/No [Last Update] - - [Next Update] - - [Current Value] - - [Notifications] 1 No/No [Time 1] 00:00 No/No [Time 2] 00:00 No/No [Time 3] 00:00 No/No [Weekday] [Monday] No/No [Day] 1 No/No [Time] 00:00 No/No [Update Screen] [Normal] No/No [QR code offset] [Vertical] 0 dot No/No [Horizontal] 0 dot No/No [Daily Checkup] - - • [Network] > [Services] > [SOTI Connect] Setting Item Initial Value Initialized by User Reset/Factory Reset [SOTI Connect] [SOTI Connect Services] [Disabled] Yes/Yes [Start Auto Enrollment] [Disabled] Yes/Yes [Auto Enrollment Server] - - [Enable Client Key Passphrase] [Disabled] Yes/Yes [Client Key Passphrase] - - [Errors, Warnings, and Notifications Push Service] [Disabled] Yes/Yes • [Network] > [Advanced] Setting Item Initial Value Initialized by User Reset/Factory Reset [ARP Announcement] [Additional] [Enabled] Yes/Yes [Periodic] 300 sec Yes/Yes [Firewall] [Enable] [Disabled] Yes/Yes [Allow Services And Ports] [Data Ports] [Enabled] Yes/Yes [FTP] [Disabled] Yes/Yes [SFTP] [Disabled] Yes/Yes [LPD] [Enabled] Yes/Yes [MAILC] [Enabled] Yes/Yes [NTP] [Disabled] No/Yes1 [Online Services] [Disabled] No/No [PING] [Enabled] Yes/Yes [Proxy] [Disabled] Yes/Yes [SATO All-In-One Tool] [Enabled] Yes/Yes [SCP] [Enabled] Yes/Yes [SNMP Agent] [Enabled] Yes/Yes [WEBC] [Enabled] Yes/Yes [WebConfig] [Enabled] Yes/Yes [Custom Settings] [TCP Source Port] [Existing Port No.] 22 80 443 465 587 8080 - [Additional Port No.] - Yes/Yes [TCP Destination Port] [Existing Port No.] 80 443 515 1024 1025 9100 - [Additional Port No.] - Yes/Yes [UDP Source Port] [Existing Port No.] 53 - [Additional Port No.] - Yes/Yes [UDP Destination Port] [Existing Port No.] 161 19541 - [Additional Port No.] - Yes/Yes [ICMP Type] [Existing ICMP Type] 0 8 - [Additional ICMP Type] - Yes/Yes • [USB]/[Bluetooth]/[NFC]/[Ignore CR/LF]/[Ignore CAN/DLE] Setting Item Initial Value Initialized by User Reset/Factory Reset [USB] [Flow Control] [STATUS4] Yes/Yes [Change USB Serial] [Disabled] No/Yes1 [Bluetooth] [Enable] [Enabled] Yes/Yes [BT Operation Mode] [Device] Yes/Yes [Name] SATO PRINTER_xxxxxxxxxxxx (BD address) Yes/Yes [PIN Code] 0000 Yes/Yes [BD Address] xxxxxxxxxxxx Yes/Yes [Firm Version] - No/No [Host BD Address] - Yes/Yes [Pairing] [Paired devices] - No/No [IAP Ready] [Enabled] No/No [iOS Reconnect] [Disabled] Yes/Yes [Authentication] [Level 4] Yes/Yes [ISI] 2048 Yes/Yes [ISW] 18 Yes/Yes [PSI] 2048 Yes/Yes [PSW] 18 Yes/Yes [CRC Mode] [Disabled] Yes/Yes [Flow Control] [STATUS4 MULTI] Yes/Yes [NFC] [I/F Enable] [Enabled] Yes/Yes [Ignore CR/LF] [Disabled] Yes/Yes [Ignore CAN/DLE] [Disabled] Yes/Yes 1Can also initialized by [Factory Reset (-Interface)] Related Topics [Reset] Back to top
