[Settings]
[LAN]
[IPv4]
After doing the settings, press the button to enable the new settings. Press the button to cancel the new settings and return to the previous settings.
You cannot change [IP Address], [Netmask], [Gateway], or [DNS] when [Mode] is [DHCP].
[Mode]
[DHCP]
Appears only if you have selected [DHCP] in the [Mode] menu and LAN is the active interface.
[IP Address]
If you have selected [Static] in the [Mode] menu, set the IP address.
[Netmask]
[Gateway]
If you have selected [Static] in the [Mode] menu, set the default gateway address.
[DNS]
[IPv6]
After doing the settings, press the button to enable the new settings. Press the button to cancel the new settings and return to the previous settings.
You cannot change [IP Address], [Prefix Length], [Gateway], or [DNS] if [Mode] is anything other than [Static].
[Mode]
[DHCP]
[IP Address]
If you have selected [Static] in the [Mode] menu, set the IP address.
[Prefix Length]
If you have selected [Static] in the [Mode] menu, set the prefix.
[Gateway]
If you have selected [Static] in the [Mode] menu, set the default gateway address.
[DNS]
If you have selected [Static] in the [Mode] menu, set the primary address of the DNS server.
[Proxy]
[Enabled]
To enable the proxy, [Server] should be set and [Exclude] must contain at least 127.0.0.1 and localhost.
[Server]
[Port No.]
[Username]
[Password]
[Exclude]
[DHCP Options]
[DHCP Options] can be set only if you have selected [DHCP] in the [IPv4] > [Mode] menu or [IPv6] > [Mode] menu.
[Update DNS (Option 81)]
[Hostname]
[Wi-Fi]
After doing the settings, press the button to enable the new settings. Press the button to cancel the new settings and return to the previous settings.
When [Wi-Fi Direct] is active, [IPv6] and [Wi-Fi Protected Setup] do not appear on the screen.
[IPv4]
After doing the settings, return to the [Wi-Fi] screen by pressing the button, and then press the button to enable the new settings. Press the button to cancel the new settings and return to the previous settings.
When [Wi-Fi Direct] is active, [Mode], [DHCP] and [DNS] do not appear. In addition, you cannot change [IP Address], [Netmask], or [Gateway] if [DHCP] or [Wi-Fi Direct] is active. [DNS] cannot be changed if [Mode] is [DHCP].
[Mode]
[DHCP]
[IP Address]
If you have selected [Static] in the [Mode] menu, set the IP address.
[Netmask]
[Gateway]
If you have selected [Static] in the [Mode] menu, set the default gateway address.
[DNS]
If you have selected [Static] in the [Mode] menu, set and check DNS server addresses.
[IPv6]
After doing the settings, return to the [Wi-Fi] screen by pressing the button, and then press the button to enable the new settings. Press the button to cancel the new settings and return to the previous settings.
When [Wi-Fi Direct] is active, this [IPv6] screen does not appear. In addition, you cannot change [IP Address], [Prefix Length], [Gateway], or [DNS] if [Mode] is anything other than [Static].
[Mode]
[DHCP]
[IP Address]
If you have selected [Static] in the [Mode] menu, set the IP address.
[Prefix Length]
If you have selected [Static] in the [Mode] menu, set the prefix.
[Gateway]
If you have selected [Static] in the [Mode] menu, set the default gateway address.
[DNS]
If you have selected [Static] in the [Mode] menu, set the primary address of the DNS server.
[Proxy]
[Enabled]
To enable the proxy, [Server] should be set and [Exclude] must contain at least 127.0.0.1 and localhost.
[Server]
[Port No.]
[Username]
[Password]
[Exclude]
[DHCP Options]
[DHCP Options] can be set only if you have selected [DHCP] in the [IPv4] > [Mode] menu or [IPv6] > [Mode] menu.
[Update DNS (Option 81)]
[Hostname]
[Wi-Fi Protected Setup]
[Button (PBC)]
1.
Select [Button (PBC)] in the [Wi-Fi Protected Setup] menu and press the button.
2.
When [Scanning...] appears on the screen, press the WPS button on the access point of the wireless LAN device.
3.
When the connection to the access point is established, [Successfully configured.] appears on the screen.
When the connection to the access point is failed, [Failed to find an Access Point.] appears on the screen.
[PIN]
1.
Select [PIN] in the [Wi-Fi Protected Setup] menu and press the button.
2.
When [Scanning...] appears on the screen, set the PIN code shown on the screen to the access point of the wireless LAN or computer.
3.
When the connection to the access point is established, [Successfully configured.] appears on the screen.
When the connection to the access point is failed, [Failed to find an Access Point.] appears on the screen.
[Wi-Fi Direct]
The Wi-Fi Direct function is enabled if you have selected [Infrastructure] in the [Mode] menu. If you have changed the setting from [Ad-hoc] to [Infrastructure] in the [Mode] menu, reboot the product before setting the Wi-Fi Direct function.
1.
Set the device name for the product using [Device Name]. You can enter 1 to 32 characters. Alphabets (capital and small letters), numbers and symbols can be used.
Press the button to return to the [Wi-Fi] menu and press the button to enable changes.
2.
Select [Connect] to search and show the connectable device names or to accept connection requests when the product is the GO (Group Owner).
3.
Select [Start Group] if you want to start a new persistent group or select a group from the list.
4.
Select [Remove Group] to remove the persistent group in step 3.
6.
Select [Disconnect] if you want to stop the connection.
When Wi-Fi Direct is active, [Device Name] cannot be changed.
[Start Group] and [Remove Group] are shown only if Wi-Fi is active and the product is not connected to a Wi-Fi Direct network.
[Remove Group] is shown if Wi-Fi is active and the product is connected.
[Band]
Enabled only if you have selected [Infrastructure] in the [Mode] menu.
[All]
[2.4 GHz]
[5 GHz]
[SSID]
[Hidden SSID]
[Mode]
[Infrastructure]
[Ad-hoc]
[Channel]
[Channel] can be set only if you have selected [Ad-hoc] in the [Mode] menu.
[Security]
[None]
[WEP]
[WPA2/WPA]
[WPA2]
[Dynamic WEP]
If you have selected [Ad-hoc] in the [Mode] menu, only [None] and [WEP] will be available.
[WEP Conf.]
Appears if you have selected [WEP] in the [Security] menu.
[Authentication]
[Open System]
[Shared Key]
[Key Index]
[Key #1] to [Key #4]
[WPA Conf.]
Appears only if you have selected [WPA2/WPA] or [WPA2] in the [Security] menu.
[WPA Authentication]
[Personal (PSK)]
[Enterprise (802.1x)]
[CCKM]
[PSK]
Appears only if you have selected [Personal (PSK)] in the [WPA Authentication] menu.
[EAP Conf.]
Appears only if you have selected items other than [Personal (PSK)] in the [WPA Authentication] menu or if you have selected [Dynamic WEP] in the [Security] menu.
[EAP Mode]
[FAST]
[LEAP]
[PEAP]
[TLS]
[TTLS]
[Inner Method]
Appears only if you have selected [FAST], [PEAP], or [TTLS] in the [EAP Mode] menu.
If you have selected [FAST] in the [EAP Mode] menu, the option is [AUTO] only.
If you have selected [PEAP] in the [EAP Mode] menu, the option is [MSCHAPv2] only.
If you have selected [TTLS] in the [EAP Mode] menu, the options are [MSCHAPv2], [MSCHAP], [CHAP], and [PAP].
[Username]
[Password]
[Anon. Outer ID]
Appears if you have selected [FAST], [PEAP], or [TTLS] in the [EAP Mode] menu.
[Verify Server Cert.]
[Private Key P/W]
Appears only if you have selected [TLS] in the [EAP Mode] menu.
[PAC Auto Provisioning]
[PAC P/W]
Appears only if you have selected [FAST] in the [EAP Mode] menu and if you have selected [Disabled] in [PAC Auto Provisioning].
[Interface]

Back to top