TOP > Adjusting the Product > Initializing the Product > List of Initial Values > [Printing] Menu [Printing] Menu Initial values refer to the values set for the product when it was shipped from the factory. If you reset the product, the values set in the product are initialized. The table below shows the initial value of each setting item and whether it would be initialized. • Normally, it is not necessary to perform the initialization. Doing an initialization removes all the product's settings that the customer changed. Setting Item Initial Value Initialized by User Reset/Factory Reset S84NX S86NX [Label Length] 203 dpi 20000 dots 305 dpi 18000 dots 609 dpi 9600 dots 203 dpi 20000 dots 305 dpi 18000 dots Yes/Yes [Label Width] 203 dpi 832 dots 305 dpi 1248 dots 609 dpi 2496 dots 203 dpi 1340 dots 305 dpi 2010 dots Yes/Yes [Auto Measure] [Disabled] Yes/Yes [Printing Mode] [Use Ribbon] Yes/Yes [Ribbon Near End] [Enabled] Yes/Yes [Speed] 203 dpi 6 ips 305 dpi 6 ips 609 dpi 3 ips 203 dpi 6 ips 305 dpi 6 ips Yes/Yes [Sensor Type] [Gap] [None] (When [Print Mode] is [Linerless]) Yes/Yes [Micro Label Print Mode] [Micro Label Print Mode] [Disabled] Yes/Yes [Auto Label Length Detection] [Enabled] Yes/Yes [Label Length Averaging Count] 3 Yes/Yes [Label Length] 203 dpi 320 dots 305 dpi 480 dots 609 dpi 960 dots 203 dpi 320 dots 305 dpi 480 dots Yes/Yes [Print Mode] [Dispenser] Yes/Yes [Backfeed] [Backfeed] Before (If [Print Mode] is set to [Dispenser], [Dispense & Print] or [Linerless]) None (If [Print Mode] is set to [Continuous]) Yes/Yes [Backfeed Start] [SIGNAL] Yes/Yes [Backfeed Timing] 100 Yes/Yes [Darkness] 6 Yes/Yes [Imaging] [Vertical] 0 dot Yes/Yes [Horizontal] 0 dot Yes/Yes [Advanced] [Calibrate] [Auto-calibration] [Gap + I-Mark] - [GAP Levels] Value adjusted by the factory No/No [GAP Slice Level] Auto No/No [I-Mark Levels] Value adjusted by the factory No/No [I-Mark Slice Level] Auto No/No [Head Check] [Off] Yes/Yes [Head Check Mode] [Always] Yes/Yes [Every Page] 1 Yes/Yes [Check Media Size] [Disabled] Yes/Yes [Adjustments] [Offset] 0 dot No/No [Pitch] 0 dot No/No [Pitch Offset] 0 dot No/No [Darkness Adjust] 50 No/No [Start Online] [Enabled] Yes/Yes [Feed After Error] [Disabled] Yes/Yes [Feed At Power On] [Disabled] Yes/Yes [Finisher Feed] 0 dot ([Standard]) Yes/Yes [Feed Speed] [Sync with Print Speed] [Enabled] Yes/Yes [Feed Speed] 6 ips Yes/Yes [Backfeed Speed] 6 ips Yes/Yes [Paper End] - Yes/Yes [Sensor Type] [Using I-mark] Yes/Yes [Paper End Distance] 203 dpi 120 dots 305 dpi 180 dots 609 dpi 360 dots Yes/Yes [Head Base Position] [Standard] Yes/Yes [Prioritize] [Commands] Yes/Yes [Reprint] [Disabled] Yes/Yes [Print End Position] 0 dot Yes/Yes [Calendar Setting Mode] * For the items below this menu, refer to the table that follows. [Ribbon Tension Adjustment] 203 dpi 12 305 dpi 5 609 dpi 1 Yes/Yes [Printing Operations] [Throughput Mode] [Disabled] Yes/Yes [Extended Backfeed Operation] [Disabled] Yes/Yes [Page Clipping Mode] [Disabled] Yes/Yes [Feed Offset] 0 dot Yes/Yes [Backfeed Offset] 0 dot Yes/Yes • [Calendar Setting Mode] Setting Item Initial Value Initialized by User Reset/Factory Reset S84NX S86NX [Calendar Reprint] [Enabled] Yes/Yes [Day of Week Code] [Sunday] 1 Yes/Yes [Monday] 2 Yes/Yes [Tuesday] 3 Yes/Yes [Wednesday] 4 Yes/Yes [Thursday] 5 Yes/Yes [Friday] 6 Yes/Yes [Saturday] 7 Yes/Yes [Month Code] [January] A Yes/Yes [February] B Yes/Yes [March] C Yes/Yes [April] D Yes/Yes [May] E Yes/Yes [June] F Yes/Yes [July] G Yes/Yes [August] H Yes/Yes [September] J Yes/Yes [October] K Yes/Yes [November] L Yes/Yes [December] M Yes/Yes [Case Format] [Mixed] Yes/Yes [Calendar Check] [Enabled] Yes/Yes [Work Shift Setting Mode] Yes/Yes 1 [Shift Code] [Disabled] Yes/Yes [Shift Time] 00:00 Yes/Yes [Shift Name] - Yes/Yes 2 [Shift Code] [Disabled] Yes/Yes [Shift Time] 00:00 Yes/Yes [Shift Name] - Yes/Yes 3 [Shift Code] [Disabled] Yes/Yes [Shift Time] 00:00 Yes/Yes [Shift Name] - Yes/Yes Back to top
